技术应用
工业扫查器首页 > 新闻专题 > 集团新闻
  • 跟贴排行
  • 点击排行
    • 腐蚀成像解决方案
    • VersaMouse扫查器
    • Wing(翼形)扫查...
    • GLIDER(滑动)扫...
    • Chain(链式)扫...
    • HSMT-X03扫查器
    • HSMT-Flex 扫查器
    • HSMT-Compact(紧...
即时新闻
  • 精彩图片
  • 热门推荐
  • 产品展示
Wing(翼形)扫查器
发布时间:2015-05-29


WING(翼型)扫查器

WING(翼型)扫查器是一款用于手动超声检测的双轴扫查器。扫查器的一个轴可以弯曲,可严密地附着在被测工件的曲面上。WING扫查器带有真空吸头,可以极好地适用于非铁磁性材料的表面检测。

概览:


The WING™ Scanner is a two-axis scanner for manual ultrasonic inspections. One scanning axis is flexible and conforms to the contour of the part being inspected. Vacuum cups make the WING Scanner well-suited for nonferromagnetic surface inspections.

Typical applications include the inspection of friction stir welding (FSW) and the inspection to detect delamination, cracks, and corrosion on plates and airplane fuselage.

Standard inclusions

  • Two integrated encoders for X and Y axes

  • 5 m encoder cable compatible with TomoScan FOCUS LT™, and OmniScan® using supplied adaptor

  • Adjustable probe holder

  • 1 PA 40 mm × 55 mm yoke

  • 1 TOFD-P/E 31.75 mm yoke

  • Irrigation tubing and fitting

  • Transport case

Options

  • Couplant-Feed Units



特性:

  • Two encoded axes for X-Y scans

  • Axis positioning with minimal backlash

  • Vacuum cups mounted on the flexible axis ease installation on both concave and convex nonferromagnetic surfaces.

  • Scanner can be used vertically or upsidedown using Venturi vacuum cups (WING Scanner "V" models only).
    NOTE: The scanner must always be secured with a lanyard when used on vertical or upsidedown surfaces.

  • Suitable for phased array and conventional UT inspection techniques using one probe

  • Can operate with an OmniScan® or TomoScan FOCUS LT™ acquisition unit.

  • Also available in a manually activated vacuum-cup version that eliminates the need for air supply (WING Scanner H1 model)

Flexible X-axis

  • Very flexible contour-following track

  • Encoder module follows the flexible track (resolution: 39.7 steps/mm).

  • Locking lever on the encoder module

  • Integrated loop on one end to secure the scanner against accidental falls.

Rigid Y-axis

  • 16 mm diameter hard-anodized aluminum shaft with stainless steel toothed rack

  • Shaft is mounted on a pivot, allowing constant contact between the probe and the part.

  • Shaft does not move under its own weight when the indexing dial is engaged.

  • Fully adjustable and tool-free, probe-alignment device

  • Indexing increments: 0.5 mm and 1 mm

  • Axis-locking thumb screw


技术规格:


Wing Scanner V1Wing Scanner V2Wing Scanner H1
X-axis stroke (mm)9401940940
Y-axis stroke (mm)510510510
Vaccum generation *Venturi with air supplyManually activated levers
Minimum external radius (mm)360380450
Minimum internal radius (mm)770770770
Holding force (kg/cup)303011
Number of cups10198
Total weight (kg)6.38.87.0
Overall scanner length (X-axis) (mm)139523951120
Overall scanner length (Y-axis) (mm)790790790
Total height (mm)157157165
* For "V" models, compressed air characteristics must correspond to the following specifications:
Required pressure: 490 kPa to 690 kPa (71 psi to 100 psi)
Flow rate: 566 nl/min (20 SCFM) minimum

PDF版产品信息:


GLIDER Manual X-Y Scanner

Wing Scanner Contour-Following X Y Manual Scanner




手册:

Wing Scanner User's Manual


 
网站地图 北京德宇泛美测试技术有限公司版权所有